1.Waterway / Humidification system consumables (Highest wear, most frequent replacement) Humidification tube / Stainless steel heating water jacket Function: Heats purified water to generate steam for humidification; prone to perforation and leakage caused by long-term scale corrosion.Replacement cycle: 612 months (3 months if water quality is poor). Humidification tank / Water tank seal Prevents leakage from the water reservoir, rubber hardens and ages due to prolonged high-temperature expos...
Find out More Sep 17, 2026
Equipment definition and corrosion principle: The sulfur dioxide test chamber (also known as a gas corrosion test chamber) is designed to simulate acidic, sulfur dioxide-laden atmospheressuch as those found in industrial zones, areas affected by acid rain, or chemical plant vicinities. It accelerates the assessment of the resistance of metal platings, coatings, electronic contacts, and hardware components to sulfur-induced corrosion. Corrosion mechanism: Within the sealed chamber, a high-tempera...
Find out More Sep 17, 2026
1. Wavelength and spectrum (Key difference) UVA-340: 295365 nm Perfectly matches the UV spectrum of sunlight at the Earths surface, contains virtually no short-wave UV that does not exist in the natural environment, resulting in aging effects that closely mirror real-world outdoor exposure. UVB-313: 280315 nm Contains significant amounts of short-wave UV rarely found in nature; possesses extremely high photon energy. It accelerates aging 23 times faster than UVA-340 and is prone to producing art...
Find out More Sep 14, 2026
Under what circumstances do the UV lamps (UVA/UVB) in a UV aging chamber need to be replaced? 1. Rated service life (Industry standard) 1) UVA-340 light tube Rated effective life: 1500 hours Slow filament degradation, stable spectrum, and more gradual decay under high-humidity conditions (60~90% RH). 2) UVB-313 light tube Higher short-wave energy and significant filament heat generation result in a shorter lifespan: 1,0001,500 hours. Long-term operation in 90% RH condensation mode can further re...
Find out More Sep 14, 2026
This section covers 9 core dimensions: vacuum pressure rating, operating temperature, wiring medium, sealing structure, electrical performance, material, usage frequency, standard compliance, and quantity allowance. It encompasses two types of structures: rubber-pressurized sealing ports and KF vacuum feedthrough ports. I. Vacuum/Minimum Pressure Rating (First Priority, Determines Port Type) The higher the negative pressure and altitude, the more stringent the sealing requirements. This directly...
Find out More Aug 22, 2026
I. Similarities for altitude chamber and vacuum oven 1. Same Basic Structure Both utilize a sealed, pressure-resistant stainless steel chamber, vacuum unit (rotary vane vacuum pump), vacuum gauge, sealed door, PID temperature control, and programmable controller. They all rely on evacuation to create a negative pressure environment, and the chambers are reinforced to prevent deformation during vacuuming. 2. Overlapping Physical Principles Both achieve low-temperature dehydration, solvent removal...
Find out More Aug 22, 2026
We commonly use two types of salt spray nozzles in salt spray test chambers: quartz glass nozzles and titanium alloy nozzles. Below are the characteristics of these two nozzles; customers can choose the appropriate nozzle based on their demand. 1. Glass Nozzle (Borosilicate/Quartz) ✅ Advantages - High atomization precision: smooth inner wall, uniform pore size, droplets 1-5m, uniform settling, conforming to GB/T 10125 and ISO 9227. - Strong chemical inertness: Resistant to NSS/AASS/CASS salt s...
Find out More May 06, 2026
I. Precautions Before Start-up 1. Check that the power supply, wiring, and grounding wire are secure, free from aging, damage, or loose connections. Operation with a single phase is strictly prohibited. 2. Check that the heating elements, temperature control probes, and thermocouples are intact, and that the probes are not misaligned or have accumulated ash or coke. 3. Clean the furnace thoroughly, removing any debris, oil, or flammable materials. Ensure the ventilation and dehumidification syst...
Find out More Apr 20, 2026
Thermal shock chambers, rapid temperature change chambers, and walk-in constant temperature and humidity chambers, if using water cooling way for heat dissipation , they require use chillers, cooling towers, or air conditioning condensate. Below is a comparison of the advantages and disadvantages of these three methods for equipment cooling/circulating water. First, clarify the application: Generally used for testing machines, cold shock chambers, injection molding, equipment heat dissipation, a...
Find out More Apr 08, 2026
I. Similarities for UV aging chamber and xenon lamp aging chamber: - Both are used for weathering and light aging tests, simulating fading, cracking, powdering, and embrittlement caused by sunlight exposure. - Both are artificially accelerated aging processes, faster and more repeatable than outdoor exposure. - Both can be equipped with spray, condensation, and temperature and humidity control to simulate rain and dew environments. - Test results are used for material selection, quality inspecti...
Find out More Mar 23, 2026
In industrial production and product design, the corrosion resistance of materials is a crucial consideration. Especially in marine, coastal, or high-humidity environments, the corrosion rate of materials accelerates significantly, affecting not only the aesthetics of products but, more importantly, their functionality and safety. To quickly assess the corrosion resistance of materials in these environments, salt spray testing has emerged. This article will delve into salt spray testing, particu...
Find out More Feb 28, 2026
Salt spray test chamber must use deionized or distilled water. Tap water and mineral water are strictly prohibited. Core Water Quality Requirements (National Standard/International Standard): Conductivity: 20 S/cm (25℃) Purity: Free of impurities, heavy metals, minerals, and organic matter. Applications: This type of water is used for preparing salt solutions, sealing tanks, saturators, and water replenishment. Why cant tap water/mineral water be used for testing? Containing calcium, magnesium...
Find out More Feb 28, 2026
The answer is no. Please read below mentioned three reasons. Material and Manufacturing Mismatch: Constant temperature and humidity chamber wet-bulb gauze is mostly made of ordinary degreased cotton/blended fabrics, with short fibers and low density. Composite salt spray (salt spray + humidity + drying cycle) will cause the gauze to harden rapidly, form salt deposits, and shed fibers, clogging the nozzle and contaminating the sample. 2. Poor Corrosion Resistance: Salt spray contains high concent...
Find out More Feb 28, 2026
It depends on the types of equipment in the same room. Some can, some cannot. 1. Equipment that can be placed together: - Ordinary non-metallic equipment (plastic, cement, rust-free) - Industrial equipment that has been properly protected against corrosion and sealed. 2. Equipment that absolutely cannot be placed in the same room: - Precision instruments, multimeters, oscilloscopes, power supplies - Computers, servers, monitoring equipment - Electroplated/painted/hardware finished products, prod...
Find out More Feb 28, 2026
Salt spray test chambers have strict standards for water and salt water, which directly determine the reliability of the results and the lifespan of the equipment. I. Test Water (Required) ✅ Qualified Water (Choose one) - Deionized water/Distilled water (Preferred) - Conductivity: 20S/cm (Grade I water 5S/cm is more stable) - Total dissolved solids (TDS): 200ppm - Free of calcium, magnesium, iron, chloride, carbonate, and other impurities - Grade II deionized water (when conditions are limited...
Find out More Feb 24, 2026
The lifespan of a constant temperature and humidity chamber/climate chamber is affected by a variety of factors. Generally speaking, qualified equipment, with normal use and maintenance, typically has a service life of around 8-15 years. What should we do to extend the climate chamber service time, below are the influence factors for the service time. Specific lifespan variations are primarily determined by the following factors: - Equipment quality: Equipment from reputable brands and using hig...
Find out More Jul 30, 2025
How to choose air-cooled/water cooled xenon lamp weathering chcamberis primarily based on the test standard, power requirements, sample characteristics, and application scenario. The key difference lies in the xenon lamp heat dissipation method and applicable scope: I. Applications of Air-Cooled Xenon Lamps - Low- and medium-power testing: Xenon lamps have low power (typically below 3.5kW) and generate relatively little heat. Air cooling (using fans to force air circulation to dissipate heat) ca...
Find out More Jul 30, 2025
The application areas of linear and nonlinear temperature ramp test chambers are primarily determined by the degree to which their temperature characteristics match the test requirements, as follows: 1. Main Application Areas of Linear Temperature Ramp Test Chambers Because they achieve uniform and stable temperature changes, linear temperature ramp test chambers are suitable for testing scenarios requiring standardization and high repeatability. Typical applications include: - Electronics and S...
Find out More Jul 30, 2025
The key difference between a cyclic salt spray test chamber and a standard salt spray test chamber lies in the complexity of the simulated environment and the diversity of test conditions. The specific differences are as follows: 1. Differences in Simulated Environments - Standard salt spray test chambers can only simulate a single salt spray corrosion environment. They primarily evaluate the corrosion resistance of products in a constant salt spray environment by continuously or intermittently...
Find out More Jul 30, 2025
Selecting dust suitable for a dust test chamber requires considering the test standard, dust characteristics, and test objectives to ensure accurate and comparable test results. The key steps and key points are as follows: 1. Prioritize compliance with test standard requirements - Identify the specified dust type based on the products corresponding international/industry standards (such as IEC 60529, ISO 12103, GB/T 4208, etc.). - Most Common Standards: Almost all common standards require the us...
Find out More Jul 08, 2025